P2646 honda element - Wiring Issue – P2646 indicates that the voltage from the VTEC/Rocker oil pressure switch is low. This means that a wiring issue very well could be at fault. Take a look at the wiring harness where it plugs into this switch. Make sure that it is undamaged and securely plugged in. Trace the wiring back and see if it is damaged anywhere.

 
If you’re facing the persistent P2646 and P2647 codes in your Honda Element, causing the engine to enter “limp mode” at approximately 3,000 RPM, you’re …. Jfk assassination gif

Just took my dads 2006 Element with 127k from him since he bought a new car and figured Id use this one for work. Had a check engine light on with code P2646 on it. Everything I have seen says vtec solenoid. Looks to be a common code. What should I start with first? Saw 2 different parts that came up.Working on a 2006 Honda element, car has code p2646 and it goes into limp mode, vtec switch and solenoid replaced, oil level good and clean, when solenoid activates over 2500 rpm, switch is off, dont know what else could be. Thanks. Submitted: 8 months ago. Category: Honda. Show More.Oh Crap, P2646 is back. I bought an 03 element with 265,000 miles on the car. It started to thrown the P2646 code and I tried everything to get rid of it. I took it to my local mechanic and he measure the oil pressure and cylinder pressure, sure enough the engine was weak.#1 · Jan 1, 2023. Ok I got code P 2646 "rocker arm actuaror" acording to forum or youtube I bought in Napa vtec solenoid "Dorman" after change super happy no engine light, VSA …How to fix Honda code P2646 VTEC for free. You're going to want to try and clean the screens for the spool valve the VTEC valve and one other screen on the f...Constant P2646 and P2647 VTEC issues. Replaced the spool valve / vtec valve with a genuine honda part. Drove fine for 2 weeks and codes are back. I had a oil change with synthetic 5w-20 and checked for clogged …After restart, only the check engine light is on, but the VSA/AWD lights come on after accelerating and experiencing the first "surge". The code pulled is P2646 on my 2008 Element, which is "Rocker Arm Actuator Stuck Bank 1". The original fix was to replace the VTC Oil Control Valve (Rocker Arm Oil Pressure Switch) as well as the Variable …Oh Crap, P2646 is back. I bought an 03 element with 265,000 miles on the car. It started to thrown the P2646 code and I tried everything to get rid of it. I took it to my local mechanic and he measure the oil pressure and cylinder pressure, sure enough the engine was weak. Step 2 is to buy a new Honda pressure switch, not the whole block, and replace the old one in the module. Solder two wires directly to the pins. Use 18AWG auto wire, cut two lengths about a foot long. Pot the whole thing in RTV and let it cure. Re-install the block and cut the connector off the harness. P2646 is an OBD-II code for the engine control module when the ‘A’ rocker arm actuator control circuit for bank 1 is malfunctioning or stuck. It can reduce engine performance and cause a loud noise. The …18 posts · Joined 2005. #1 · Jul 25, 2010. Had a scare the other day while out of town about 40 miles away. All of a sudden, my '05 Element engine started bucking badly at anything above 3000 RPM's. I happened to find a recommended transmission shop near the auto parts store that I stopped in to check on the price of a diagnostic code reader.Please leave a comment, thumbs up the video, and don't forget to subscribe if you enjoy our videos! Thank you!💜 Our channel is family-friendly. 💜 A subreddit for Honda Element enthusiasts! The Honda Element was a compact crossover SUV based on a modified CR-V platform, manufactured in East Liberty, Ohio and offered in front-wheel and all-wheel drive formats in the United States and Canada from model years 2003 through 2011. Get Additional Help. A P2646 code is an OBD code for the Engine Control Module (ECM) detecting that the “A” rocker arm actuator control circuit for bank 1 has a performance issue or is stuck ...Oh Crap, P2646 is back. I bought an 03 element with 265,000 miles on the car. It started to thrown the P2646 code and I tried everything to get rid of it. I took it to my local mechanic and he measure the oil pressure and cylinder pressure, sure enough the engine was weak.The Honda Element was a compact crossover SUV based on a modified CR-V platform, manufactured in East Liberty, Ohio and offered in front-wheel and all-wheel drive formats in the United States and Canada from model years 2003 through 2011. ... My E has actually been behaving as of late but just started throwing the P2646 code again. Oil is 1500 ...Common p2646 question. Hi all, I am new to the forum and hoping for some help. I have an 04 cry and code P2646 popped up. So the first thing I did, from a suggestion on line was pulled off the Vtech selonoid and cleaned the screen filter and changed oil. But I didn’t have correct oil, I used 5w30 synthetic, 4 qts and topped off with reg 5w30 ...Good luck trying to buy a Toyota, Kia or Honda. These auto brands have the lowest supply of cars available for sale at dealerships now. By clicking "TRY IT", I agree to receive new...When it comes to purchasing a Honda generator, finding the best deals and discounts can make a significant difference in your overall budget. With so many options available in the ...Apr 11, 2010 · Honda / Element / 2006 / what is p2646 ; What is p2646 . 2006 Honda Element. Asked by Visitor in Brentwood, CA on . April 11, 2010. what does p2646 mean . 1 reply ... 2003-11 Element ALL ALL 2007-11 Fit ALL ALL REVISION SUMMARY Under REPAIR PROCEDURE, illustrations in step 2 specific to 2008-12 Accord PZEV were added along with additional FRT. SYMPTOM The MIL comes on with one of these DTCs: • P2646/P2651 (rocker arm oil pressure switch circuit low voltage). Getting control of your finances can be tough, but a good budget can help. Although a budget can vary dramatically from one person to the next, many elements are the same, includin...P2646 Honda Code - Rocker Arm Oil Pressure Switch Circuit Low Voltage. How to Fix. Check the 'Possible Causes' listed above. Visually inspect the related wiring … In this video, young mechanic Aiman discusses P2646, which is an OBD-II generic code for the engine control module (ECM) detecting the 'A' rocker arm actuato... lostwater said: Hi! I am looking to buy a Honda Element and reading here there are many many posts about the P2646 code with the oil pressure switch and going into limp mode. I've seen these for the 2003-2006 generation Element, but haven't yet seen a post mentioning the problem in later Elements (2007 on) when the motor changed (10 more hp, etc). Get Additional Help. A P2646 code is an OBD code for the Engine Control Module (ECM) detecting that the “A” rocker arm actuator control circuit for bank 1 has a performance issue or is stuck ... Just took my dads 2006 Element with 127k from him since he bought a new car and figured Id use this one for work. Had a check engine light on with code P2646 on it. Everything I have seen says vtec solenoid. Looks to be a common code. What should I start with first? Saw 2 different parts that came up.(RTTNews) - Honda, the world's largest motorcycle manufacturer, has announced its plans to launch electric motorcycles. Honda announced it would ... (RTTNews) - Honda, the world's...Timing on a Honda Element is controlled by the cam position sensors which are located on the left end of the engine just below the valve cover. If a sensor is failing or its cam plate that's inside at the end of the camshaft is loose or worn, the engine will not start reliably and then not at all. ... The only code I had was p2646 and since the ...2003 Honda Element EX AT 2WD 355k+ miles, 2003 Honda CRV EX AT AWD 310k+ miles, 2018 Ford Transit LR XLT RWD 40k+ miles. Save Share. ... Add me to the list experiencing sudden p2646 @ 181k miles on my 05 EX.. Came on while leaving for work today, giving me a harsh kick @ 3k rpms. Won't rev any higher in gear, just harsh …The code came up P2646 (rocker arm off or stuck). I took the info and drove about 20 more total miles and then it happened once again. I looked at the some info online and decided it might be VTEC oil pressure switch related as the code diagnostics said. SO I picked up one up and installed it.Just took my dads 2006 Element with 127k from him since he bought a new car and figured Id use this one for work. Had a check engine light on with code P2646 on it. Everything I have seen says vtec solenoid. Looks to be a common code. What should I start with first? Saw 2 different parts that came up.P2646: Your Engine’s Secret Alarm Bell. The P2646 code refers to the ‘A’ Rocker Arm Actuator System PerformanceStuck Off Bank 1. The Engine Control Module (ECM) controls the oil hydraulic circuit through the Rocker Arm Actuator. The Rocker Arm Actuator adjusts the engine’s valve timing through the variable valve timing (VVT) system.About a year ago my 04 E (180,000miles)started bottoming about at 60mph. The engine light came on and the code was P2646, rocker arm stuck in off position. After some research I replaced the vvt solenoid and performed an oil change. The engine light went off and all was good. Fast forward to now, almost a year the the day and the same …In this video I describe common issues and fixes for Honda 2.4L engines with a p2646. #honda #crv #p2646 #automotive #diagnosis #2.4 #2.4L #tips #tricks #tec...Learn what the P2646 code means, how it affects your engine performance, and what you can do to fix it. Find out the possible causes, symptoms, and solutions for this common Honda Element problem.P2646 Rocker Arm Oil Pressure Switch Circuit A Low VoltageCustomer brought in the car and thought the transmission was slipping and free reving. I diagnosed ...Honda Element: 2005 honda element 2.4L code PO135 AF sensor 2005 honda element 2.4L code PO135 AF sensor S1 heater circuit malfunction, replaced o2 sensor, 2nd code P2646 VTEC pressure switch circuit voltage low, replaced with new switch update version still d …Common p2646 question. Hi all, I am new to the forum and hoping for some help. I have an 04 cry and code P2646 popped up. So the first thing I did, from a suggestion on line was pulled off the Vtech selonoid and cleaned the screen filter and changed oil. But I didn’t have correct oil, I used 5w30 synthetic, 4 qts and topped off with reg 5w30 ...But I have the old p2646 thing going on currently, have replaced the whole solenoid, not just the oil pressure switch, have been changing the oil every 1000 miles, and for the last 3500 miles or so, I'm still getting the CEL, and for the same p2646.Faulty Components: Oil Pressure Switch, VTEC Solenoid, or Actuator. The oil pressure switch is critical. It’s like the referee in a sports game, making important calls. If it’s faulty, it can miscommunicate the engine’s status. This leads to the P2646 code. The VTEC solenoid and actuator are also vital.Step 1: Diagnostic Scan. Before diving into any repairs, it’s essential to perform a diagnostic scan to confirm that code P2646 is indeed the issue. You can use an OBD-II scanner to retrieve the trouble codes from your Honda Accord’s ECM. Make sure to write down the codes displayed for future reference.Wiring Issue – P2646 indicates that the voltage from the VTEC/Rocker oil pressure switch is low. This means that a wiring issue very well could be at fault. Take a look at the wiring harness where it plugs into this switch. Make sure that it is undamaged and securely plugged in. Trace the wiring back and see if it is damaged anywhere.VTEC SOLENOID REPLACEMENT AND /OR JUST SCREEN REPLACEMENT. HONDA 2.4L ENGINE 4 CYLINDERS. SAME ON CRV, ELEMENT ACCORD CIVIC. CHECK ENGINE LIGHT. HESITATE AND...Causes. Seriousness. Can I Still Drive? Diagnose. Difficulty of Inspecting. Get Additional Help. A P2646 code is an OBD code for the Engine Control Module (ECM) detecting that …This video is about Honda P2646 P2647 engine check code fix I-Vtec 2.4 Odyessy, Accord, Element, CRV. I go through what could be the cause of the fault code ...Only show this user. #1 · Jul 13, 2021. I have an '05 E. 187k miles. Last year it started doing that annoying crap where it acts like it has a rev limiter set to 3000 rpms. P2646. VTEC solenoid.. I replaced it with a Dorman from Oreilly's. Had a …the two things that i've seen cause this code are low oil level, and a bad vtec pressure switch. 9 times out of 10, it's a customer who's 2000 miles overdue for an oil change, and they're over a quart low. i've also seen a few leaky vtec solenoid gaskets aka spool valve gasket. check that too. Mike K.Sep 30, 2023 · Definition Meaning and Fixes for a Honda P2646 engine Diagnostic Trouble Code: ‘A’ Rocker Arm Actuator System Performance / Stuck Off Bank 1 "Rocker Arm Oil ... P2646 Honda Code - Rocker Arm Oil Pressure Switch Circuit Low Voltage. How to Fix. Check the 'Possible Causes' listed above. Visually inspect the related wiring …The Honda Element was a compact crossover SUV based on a modified CR-V platform, manufactured in East Liberty, Ohio and offered in front-wheel and all-wheel drive formats in the United States and Canada from model years 2003 through 2011. ... So I just got this p2646 code as well AFTER I just paid $1600 to get a new catalytic converter. Took it ...The code came up P2646 (rocker arm off or stuck). I took the info and drove about 20 more total miles and then it happened once again. I looked at the some info online and decided it might be VTEC oil pressure switch related as the code diagnostics said. SO I picked up one up and installed it.The dreaded P2647. I have been using this great forum to try and solve my CEL code. So far I have changed the oil pressure switch, cleaned both screens and the front and back of the head and even changed to a honda oil filter. So far I haven't fixed anything. The light only comes on when it's cold and once warmed up it will go away.Sep 30, 2023 · Definition Meaning and Fixes for a Honda P2646 engine Diagnostic Trouble Code: ‘A’ Rocker Arm Actuator System Performance / Stuck Off Bank 1 "Rocker Arm Oil ... It seems that there are a lot of Element enthusiasts out there, and this site is quite active, but not a whole lot of get togethers. I have been on this site for 3 years, and …In this video, young mechanic Aiman discusses P2646, which is an OBD-II generic code for the engine control module (ECM) detecting the 'A' rocker arm actuator control circuit for bank 1 has a performance problem or is stuck in the off position.Mechanic for Honda: Tech413. This code is usually caused by a sticking VTEC oil pressure switch or low oil level. Check the oil level first if that is ok. Check the pressure switch or replace the switch. If you have access to a multimeter, I can walk you through some simple steps to check the switch.The P2646 code is likely the most difficult problem to diagnose on a Honda 2.4 VTEC engine. There is no "Just Do ..... and you'll be good to go" answer. It could be any number of issues or a combination of issues. Here are some links I have saved over the years that have been helpful: Uh - Oh!P2646 will cause your engine to go into limp mode at about 3000 rpm which is why you're experiencing the "sputtering". It is not in vain, but do not just simply throw parts at it. P0420 is a catalytic converter efficiency code; it may set the code, but shouldn't cause drivability issues like the P2646. I have (at least temporarily) solved a ...Please leave a comment, thumbs up the video, and don't forget to subscribe if you enjoy our videos! Thank you!💜 Our channel is family-friendly. 💜176 posts · Joined 2017. #5 · Jan 2, 2022. I switch to 5-30 oil over 200k miles to prevent the oil pressure drop which CAN (not does) trigger a P2646 code with loose bearing clearances on higher mileage engines. That and clean oil, and clean screens, help 90% of …Causes. Seriousness. Can I Still Drive? Diagnose. Difficulty of Inspecting. Get Additional Help. A P2646 code is an OBD code for the Engine Control Module (ECM) detecting that …P2646: Your Engine’s Secret Alarm Bell. The P2646 code refers to the ‘A’ Rocker Arm Actuator System PerformanceStuck Off Bank 1. The Engine Control Module (ECM) controls the oil hydraulic circuit through the Rocker Arm Actuator. The Rocker Arm Actuator adjusts the engine’s valve timing through the variable valve timing (VVT) system.This video is about Honda P2646 P2647 engine check code fix I-Vtec 2.4 Odyessy, Accord, Element, CRV. I go through what could be the cause of the fault code ...-P2646 VTEC OIL PRESSURE SWITCH CIRCUIT MALFUNCTION Next, took it for an oil change, in which after the tech noted the CEL turned off and now I can't get the problem to replicate. Very strange, still have an appointment with Honda on wednesday, will take the paper with me. After reading through the thread, it seems it could be a …How to diagnose code P2646 on a Honda CR-V. To diagnose code P2646 on a Honda CR-V, follow these steps: 1. Use an OBD-II scanner: Connect an OBD-II scanner to the vehicle’s diagnostic port to retrieve the specific trouble code. 2. Inspect the VVT oil pressure switch and wiring: Check the VVT oil pressure switch and its associated …A forum thread where users share their experiences and solutions for the VTEC P2646 code, which causes limp mode and low RPM in Honda Elements. See possible causes, fixes, and tips from other owners.P2646 code. Hello, I performed everything else everyone else is doing related to the Vtec pressure switch. I took an oil pressure gauge and installed it in the port for my oil pressure light in the dash. I found I have 45 psi hot idle and over 90 psi at 2700 rpms this seems wrong to me.1316 posts · Joined 2008. #2 · Mar 1, 2023. I would have to think that the P0420 and the P2646 are unrelated and troubleshoot them separate from each other. I would think that a persistent negative fuel trIm might be a cause of early cat failure, so I might consider looking at that together with the P0420.Step 1: Diagnostic Scan. Before diving into any repairs, it’s essential to perform a diagnostic scan to confirm that code P2646 is indeed the issue. You can use an OBD-II scanner to retrieve the trouble codes from your Honda Accord’s ECM. Make sure to write down the codes displayed for future reference.P2646: Your Engine’s Secret Alarm Bell. The P2646 code refers to the ‘A’ Rocker Arm Actuator System PerformanceStuck Off Bank 1. The Engine Control Module (ECM) controls the oil hydraulic circuit through the Rocker Arm Actuator. The Rocker Arm Actuator adjusts the engine’s valve timing through the variable valve timing (VVT) system.7.09K subscribers. Subscribed. 305. 29K views 7 months ago. Definition Meaning and Fixes for a Honda P2646 engine Diagnostic Trouble Code: ‘A’ Rocker Arm Actuator System Performance / Stuck Off...About a year ago my 04 E (180,000miles)started bottoming about at 60mph. The engine light came on and the code was P2646, rocker arm stuck in off position. After some research I replaced the vvt solenoid and performed an oil change. The engine light went off and all was good. Fast forward to now, almost a year the the day and the same problem ...Honda is recalling over half a million cars due to corroding parts. Over half a million Honda vehicles have been recalled after multiple reports of a rear part detaching due to cor...it would be once or so a month, then once a week, then once a day, not wont start at all. When it began to happen more often, it was only when it sat a. few hours, over night or such. it would take two or three trys cranking for like 5 seconds, to get it to start. after it started it was good, and would start again.Jan 7, 2020 · Wiring Issue – P2646 indicates that the voltage from the VTEC/Rocker oil pressure switch is low. This means that a wiring issue very well could be at fault. Take a look at the wiring harness where it plugs into this switch. Make sure that it is undamaged and securely plugged in. Trace the wiring back and see if it is damaged anywhere. Jan 24, 2019 · To diagnose the P2646 Honda code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour. thanks I read some of that, I had the p2646 code come up and i fixed that with changing the oil, I know of that issue and have fixed it on 5 elements so its not a big deal to me. This p0011 code is new to me and I dont want to go replacing parts blindly. im working on this code p0011 I read on a rsx forum they have had similar problems with ...This 2003 Honda Element seems to be possessed. The gauges stick or don't work at all, lights flash, relays click, it cranks but won't start. It also has a P2...Sep 27, 2021 · If it does not it will set the code. At 3000 rpm it should take at least 57 psi oil pressure to open the rocker arm oil pressure switch. If the oil pressure is low at that point throwing parts at it will not correct the issue. Read the info at the link below. P2646 Honda. 05 Honda Element EX currently 125000 miles: original owner Beginning in 2012 (60k miles) I threw my first P2646. Replaced the entire valve assembly. Almost every 3 years this thing rears its head and I have learned to replace both screens during the oil changes. However, I have no trust with driving my car on the freeway anymore as the first ...P2646症状：Honda Element. P2646単独で現れることは、通常、顕著な運転性の症状に対応していません。 性能および燃料のマイレッジのマイナーなすくいに気づくかもしれない。 VTCストレーナ画面が詰まっている場合は、エンジンが重い加速下で死ぬことがあり ...72 posts · Joined 2021. #1 · Mar 5, 2024. Hello! I know that the famous P2646 code has been discussed in depth, but i have a question about it that I haven’t seen addressed yet. My 2006 E (Atomic Blue) threw the code & went into limp mode 2 months ago. Did everything, replace Vtek valve with OEM, clean screens, replace oil pressure …Then the mechanic gets ill,stroke, he is now back at his shop, Element is put back toghther but mechanic now says engine is reving and he is getting following codes, PO507,P2279,P2646. He cant figure it out and really is not healthy enough to be working. The mechanic is not the same guy I took the car to as the stroke took its toll.Then the mechanic gets ill,stroke, he is now back at his shop, Element is put back toghther but mechanic now says engine is reving and he is getting following codes, PO507,P2279,P2646. He cant figure it out and really is not healthy enough to be working. The mechanic is not the same guy I took the car to as the stroke took its toll.Sep 30, 2023 · Definition Meaning and Fixes for a Honda P2646 engine Diagnostic Trouble Code: ‘A’ Rocker Arm Actuator System Performance / Stuck Off Bank 1 "Rocker Arm Oil ... Sep 9, 2019 · I got engine codes P1009 and P2646. The car runs fine. I have gotten it to go past 5000 RPMs when needed (usually accelerating to 80mph going up hill). I have read that the P2646 can usually mean a VTECH solenoid problem and usually that needs replacing if you are having trouble hitting higher RPMs. But that's not the case for me. Specifically ...

P2646 is an OBD-II code for the engine control module when the ‘A’ rocker arm actuator control circuit for bank 1 is malfunctioning or stuck. It can reduce engine performance and cause a loud noise. The …. China garden adrian michigan

p2646 honda element

-P2646 VTEC OIL PRESSURE SWITCH CIRCUIT MALFUNCTION Next, took it for an oil change, in which after the tech noted the CEL turned off and now I can't get the problem to replicate. Very strange, still have an appointment with Honda on wednesday, will take the paper with me. After reading through the thread, it seems it could be a …May 16, 2020 · P2649 P2647 P2646 ROCKER ARM ACTUATOR SYSTEM STUCK ON BANK 1 FIXHello everyone i decided to make a video how to fix a problem with one of my customers car.LI... P2646 Rocker Arm Oil Pressure Switch Circuit A Low VoltageCustomer brought in the car and thought the transmission was slipping and free reving. I diagnosed ...Jan 1, 2023 · Since low oil pressure is one of the potential causes of P2646, the real fix is new engine. However, there are many who are not yet willing to give up on an engine, and have decided to compensate for the low oil pressure by using a higher weight oil, such as 5w-30 or 5w-40. Step 2 is to buy a new Honda pressure switch, not the whole block, and replace the old one in the module. Solder two wires directly to the pins. Use 18AWG auto wire, cut two lengths about a foot long. Pot the whole thing in RTV and let it cure. Re-install the block and cut the connector off the harness.This would hurt the oil’s viscosity and trigger the P2646. Low Oil – If the dipstick is not registering oil at all, it may be too low for the VTEC system to function properly. Wiring Issue – P2646 indicates that the voltage from the VTEC/Rocker oil pressure switch is low. This means that a wiring issue very well could be at fault.Honda vehicles commonly display the diagnostic trouble code P2646. It indicates that the oil pressure switch for the rocker’s arm is malfunctioning. Often referred to as the VTEC (Variable Valve Timing & Lift Electronic Control) switch, the Rocker arm oil pressure switch verifies oil pressure in the VVT mechanism.This 2003 Honda Element seems to be possessed. The gauges stick or don't work at all, lights flash, relays click, it cranks but won't start. It also has a P2...There are multiple common causes of the P2646, so what to fix depends on what is wrong. Low oil pressure is one cause of P2646. If someone has told you that you need to replace the oil pump, I am assuming that they have measured and proven that your VTEC screens are clean and your engine oil pressure is low. ... 2003 Honda Element …Okay so to add to this set up death to a Honda issue. Becuase I too have been suffering this plaque. Long and short: First time this happened a local oil change place put 10w40 in my Element. Within a mile of the shop it blew P2646 code. Took it to my mechanic, he did a oil test and thats how I know what was put in the car.Introducing the P2646 Honda Element – the ultimate guide for all Honda enthusiasts out there! If you're a proud ownerThe “C” in Honda’s “CRV” stands for “comfortable.” The complete phrase is “Comfortable Runabout Vehicle.” The original concept of the vehicle was to provide a model with “more acti...This 2003 Honda Element seems to be possessed. The gauges stick or don't work at all, lights flash, relays click, it cranks but won't start. It also has a P2...May 16, 2020 · P2649 P2647 P2646 ROCKER ARM ACTUATOR SYSTEM STUCK ON BANK 1 FIXHello everyone i decided to make a video how to fix a problem with one of my customers car.LI... I just bought a 2006 Honda Element EX-P AWD with 158k miles. Absolutely love the car but am dealing with the much elusive p2646 code. Already changed the oil, oil filter, oil sensor, and the entire VTEC solenoid (with the correct part straight from Honda), but the car keeps bucking at 3000 rpm.Bought 2003 element. Check engine was on and code was P2646. The car didn’t want to go over 3500 rev. I replaced screens on solenoids and one extra under the lid. Problem solved. Traveled 800 miles in 2 days and on highway code popped up again. Learn how to fix ERROR CODE P2646 on your HONDA with the 2.4L engine.If this video is helpful, give it a "thumbs up" and consider subscribing to our channel.... Apr 25, 2020 · A week or so ago, check engine light comes on, scan... P2646 for the A rocker arm actuator not performing. Was not in limp mode, just sluggish. Went and got the oil changed, reset, went away for an hour and came back. A day later I pick up a brand new OEM valve spool assembly from a Honda dealership. Dark Mode; Light Mode; menu Log in.

Popular Topics